

120 rubber tube extruder

型号 XJ-65 XJ-75 XJ-90 XJ-120 螺杆直径mm 65 75 90 120 长径比 12/14：1 12/14：1 14/16：1 14/16：1 电机功率kw 22 30 45 110 螺杆转速r/min 10-70 10-70 10-70 10-70 产量kg/h 60-100 80-160 180-300 300-550 用途可以用于橡胶工业，橡胶管，暖风管，夹线胶管，内胎，胶带，子口带等其他橡胶制品的挤出成型，也可用于小型压延机的热炼供应。冷喂料橡胶挤出机和一般橡胶挤出机相比具有生产能力高，胶料温度低，电能消耗少，混合效果好，塑化均匀，产量高等特点。橡胶管冷喂料挤出机安全操作规程： 1.开机前，检查机头是否完全吻合，清除喂料口杂物，方可开机。 2.机器各部分要按工艺要求加温至规定温度，严禁将手放在加温部位上。 3.操作者的手或手指不准伸入喂料口，加料时不准戴手套，喂料口掉入杂物时，不准用手去拿，须停机处理。 4.挤出机供料时，喂料口出现塞胶等异常情况时，须停机后用工具处理。 5.机头合模时，严禁将手放在机头动作接触面，避免挤伤。 6.更换机头插件时须拿牢，机头开模时，不准在机头部位操作，两人操作要配合好，避免机头插件脱落伤人。 7.橇机头余料时，用力要适度，避免橇棒伤人。 8.供胶皮带挤胶时，严禁运转时用手拉，须停机处理。 9.操作人员使用割胶刀时，刀口不准对准自己或他人。 10.工作结束后，盖好喂料口，关闭水汽阀门，切断电源。橡胶挤出机性能特点 1. 本机采用交流电机，变频调速，其调速范围大，对生产不同规格的橡胶制品适应性大，操作方便。 2. 本机使用硬齿面橡胶挤出机减速器，其噪音低，传动扭矩大，传动平稳，维修方便。 3. 本机采用冷却喂料辊强制进料，可加工多种橡胶条料，挤压密度大，制品效果好。 4. 本机设有双通道温度自动控制仪，加热时温度波动小，根据不同加工工艺能理想的选择加热温度，并能自动控制被加热的机筒、机头的设定温度。 5. 本机采用机筒水加热，也可使用蒸气加热。机筒采用循环冷却，能即时地冷却物料，以防物料分解。

Key words:

Classification:

Rubber, rubber and plastic extrusion line

Business Hotline:

400-0319-386

Related products

Feedback

120 rubber tube extruder

Model number	XJ-65	XJ-75	XJ-90	XJ-120
Screw diameter (mm)	65	75	90	120
Length-diameter ratio	12/14：1	12/14：1	14/16：1	14/16：1
Motor power (kw)	22	30	45	110
Screw speed r/min	10-70	10-70	10-70	10-70
Yield kg/h	60-100	80-160	180-300	300-550

Use

It can be used in the rubber industry, rubber pipe, warm air pipe, wire clamp hose, inner tube, tape, Zi mouth belt and other rubber products extrusion molding, can also be used for small calender hot smelting supply. Compared with general rubber extruder, cold feeding rubber extruder has the characteristics of high production capacity, low temperature of rubber material, less energy consumption, good mixing effect, uniform plasticizing and high yield.

Safe operation rules for rubber tube cold feeding extruder:

1. Before starting the machine, check whether the machine head is completely anastomosed and remove debris from the feeding port before starting the machine.

2. All parts of the machine shall be heated to the specified temperature according to the technological requirements. It is strictly prohibited to put your hand on the heating part.

3. The operator is not allowed to extend his hand or finger into the feeding port, and is not allowed to wear gloves when feeding. When the feeding port falls into the debris, it is not allowed to take it by hand, and it must be stopped for processing.

4. When the extruder is feeding, if there is any abnormal situation such as plugging at the feeding port, it must be stopped and processed with tools.

5. When the machine head closes the mold, it is forbidden to put your hand on the contact surface of the machine head to avoid crushing injury.

6. When replacing the head plug-in, hold it firmly. When the head opens the mold, it is not allowed to operate in the head part.

7. Moderate force should be applied to avoid injury by the sled rod when the head is left over.

8. When the rubber belt is extruded, it is strictly prohibited to pull it by hand during operation, and it must be stopped for processing.

9. When the operator uses the rubber knife, the knife edge should not be pointed at himself or others.

10. After the work, cover the feeding port, close the water vapor valve and cut off the power supply.

Performance characteristics of rubber extruder

1. The machine adopts AC motor, frequency conversion speed regulation, the speed regulation range is large, the production of different specifications of rubber products adaptability, easy to operate.

2. This machine uses hard tooth surface rubber extruder reducer, its low noise, large transmission torque, smooth transmission, easy maintenance.

3. This machine adopts cooling feed roller to force feed, can process a variety of rubber strip material, high extrusion density, good product effect.

4. The machine is equipped with a double channel automatic temperature control instrument, the temperature fluctuation is small when heating, according to different processing technology can choose the ideal heating temperature, and can automatically control the heating cylinder, the setting temperature of the machine head.

5. This machine adopts cylinder water heating, can also use steam heating. The barrel is cooled by circulation, which can cool the material in real time and prevent material decomposition.