Rubber filter

型号 XJ-120 XJ-150 XJ-200 XJ-250 螺杆直径mm 120 150 200 250 长径比 5：1 5：1 5：1 5：1 电机功率kw 37 55 75 110 螺杆转速r/min 30-50 30-50 30-50 30-50 产量kg/h 200-400 350-450 400-800 600-1000 用途及特点滤胶机是利用螺杆推挤、输送作用，把胶料或再生胶中的杂质清除掉的机械。主要由螺杆、机筒、滤胶机头和传动装置等组成。滤胶机头上装有孔板及过滤网，孔板用于支承过滤网并为排料口，是沿胶料流动方向扩张的锥形孔。滤胶机安全操作规程 1．过滤之前须将机头机身预热到规定温度。 2．电机负载不能过规定值(160安培)。 3．正常过滤时，滤橡胶温度不得过140℃，是氯丁胶不得过105℃。 4．已烧焦的混合胶不得过滤，过滤后的混合胶不得有焦烧粒子。 5．冷胶不得过滤，若需过滤冷胶时，须压软之后才可过滤。 6．不得将金属等杂物加入到滤胶机中。 7．严禁用手往加料器中塞胶，或运转时用手往外取胶。滤胶机要点 1滤胶机螺杆直径一般150以上。 2长径比一般5左右。 3等距等深的螺杆结构。 4压缩比很小，很多是1. ---不压缩。 5转速慢，功率要大。----过滤效率高。至于冷却挤出机也要冷却的。滤胶机要冷却。 5、过滤网一般50目左右。滤胶机、橡胶滤胶机、内胎滤胶机用于过滤胶料的杂质，机头采用铰接的方式，安装在机身的法兰上，并用蜗轮蜗杆传动进行开锁，节约能源开锁轻便。滤胶机的机身制有螺旋型水汽通道，有良好的调温效果，并装有热电偶、测温和毫伏计显示温度。滤胶机的螺杆和衬套均采用合金钢并经氮化处理，有强度和良好的可磨性。滤胶机的减速机为渐开线圆柱齿轮传动，油池润滑体积小重量轻。

Key words:

Rubber filter

Classification:

Rubber, rubber and plastic extrusion line

Business Hotline:

400-0319-386

Related products

Feedback

Rubber filter

Model number	XJ-120	XJ-150	XJ-200	XJ-250
Screw diameter (mm)	120	150	200	250
Length-diameter ratio	5：1	5：1	5：1	5：1
Motor power (kw)	37	55	75	110
Screw speed r/min	30-50	30-50	30-50	30-50
Yield kg/h	200-400	350-450	400-800	600-1000

Application and characteristics

Rubber filter is the use of screw extrusion, conveying, the rubber material or recycled rubber in the removal of impurities in the machinery. It is mainly composed of screw, barrel, filter head and transmission device. Glue filter head

A hole plate and a filter screen are arranged on the upper part. The hole plate is used to support the filter screen and is a discharge port. It is a conical hole expanding along the flow direction of the rubber material.

Rules for safe operation of rubber filter

1. Preheat the nose body to the specified temperature before filtering.

2. Motor load cannot exceed the specified value (160 amps).

3. Normal filtration, filter rubber temperature shall not be more than 140℃, is neoprene rubber shall not be more than 105℃.

4. The burnt mixture shall not be filtered, and there shall be no burnt particles in the filtered mixture.

5. Cold glue shall not be filtered. If it is necessary to filter cold glue, it must be pressed soft before filtering.

6. Metal and other debris shall not be added to the glue filter.

7. Do not plug glue into the feeder by hand, or take glue out by hand when running.

Glue filter to point

1 The screw diameter of the glue filter is generally more than 150.

2 The length-diameter ratio is generally about 5.

3. Equal distance and equal depth screw structure.

4 Compression ratio is very small, many are 1. -- no compression. 5 Slow speed, high power. ---- High filtration efficiency.

As for cooling the extruder, it has to be cooled. The glue filter should be cooled.

5, the filter screen is generally about 50 mesh.

Rubber filter, rubber filter, inner tube filter is used to filter the impurities of rubber material, the head is hinged, installed on the flange of the fuselage, and worm gear worm drive for unlocking, saving energy and light unlocking. The body of the rubber filter is equipped with spiral water vapor channel, which has a good temperature control effect. It is equipped with thermocouple and temperature measuring millivoltmeter to display the temperature. The screw and bushing of the rubber filter are made of alloy steel and nitrized, which has strength and good grindability. The reducer of the rubber filter is driven by involute cylindrical gear, and the lubrication volume of the oil pool is small and the weight is light.